Alpine CDE-103BT Manuel du propriétaire Page 32
- Page / 39
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Installation
and Connections
Before installing or connecting the unit, please read the
following and pages 3 to 5 of this manual thoroughly for
proper use.
~Warning
MAKE
THE
CORRECT
CONNECTIONS.
Failure to make the proper connections may result
in
fire
or
product
damage.
USE
ONLY
IN
CARS
WITH
A
12
VOLT
NEGATIVE
GROUND.
(Check with your dealer
if
you are not sure.) Failure
to
do so may
result
in
fire, etc.
BEFORE
WIRING,
DISCONNECT
THE
CABLE
FROM
THE
NEGATIVE
BATTERY
TERMINAl.
Failure to do so may result in electric shock
or
injury due to
electrical shorts.
DO
NOT
ALLOW
CABLES
TO
BECOME
ENTANGLED
IN
SURROUNDING
OBJECTS.
Arrange wiring and cables
in
compliance with the manual to
prevent obstructions when driving. Cables
or
wiring that obstruct
or
hang up on places such as the steering wheel, gear lever, brake
pedals, etc. can be extremely hazardous.
DO
NOT
SPLICE
INTO
ELECTRICAL
CABLES.
Never cut away cable insulation to supply power to other
equipment. Doing so will exceed the current carrying capacity
of
the wire and result in fire or electric shock.
DO
NOT
DAMAGE
PIPE
OR
WIRING
WHEN
DRILLING
HOLES.
When drilling holes in the chassis for installation, take precautions
so as not to contact, damage
or
obstruct pipes, fuel lines, tanks
or
electrical wiring. Failure to take such precautions may result in fire.
DO
NOT
USE
BOLTS
OR
NUTS
IN
THE
BRAKE
OR
STEERING
SYSTEMS
TO
MAKE
GROUND
CONNECTIONS.
Bolts or nuts used for the brake
or
steering systems (or any other
safety-related system),
or
tanks should
NEVER
be used for
installations
or
ground connections. Using such parts could disable
control
of
the vehicle and cause fire etc.
KEEP
SMALL
OBJECTS
SUCH
AS
BATTERIES
OUT
OF
THE
REACH
OF
CHILDREN.
Swallowing them may result in serious injury.
If
swallowed,
consult a physician immediately.
DO
NOT
INSTALL
IN
LOCATIONS
WHICH
MIGHT
HINDER
VEHICLE
OPERATION,
SUCH
AS
THE
STEERING
WHEel
OR
GEARSHIFT.
IMPORTANT
Please record
the
serial number
of
your unit
in
the space provided
below and keep
it
as a permanent record. The serial number or the
engraved serial number
is
located
on
the bottom
of
the unit.
30-EN
Doing so may obstruct forward vision
or
hamper movement etc.
and results in serious accident.
~Caution
HAVE
THE
WIRING
AND
INSTALLATION
DONE
BY
EXPERTS.
The
wiring and installation
of
this unit requires special technical
skill and experience. To ensure safety, always contact the dealer
where you purchased this product to have the work done.
USE
SPECIFIED
ACCESSORY
PARTS
AND
INSTALL
THEM
SECURELY.
Be sure to use only the specified accessory parts. Use
of
other than
designated parts may damage this unit internally
or
may not
securely install the unit
in
place. This may cause parts to become
loose resulting in hazards
or
product failure.
ARRANGE
THE
WIRING
SO
IT
IS
NOT
CRIMPED
OR
PINCHED
BY
A
SHARP
METAL
EDGE.
Route the cables and wiring away from moving parts (like the seat
rails)
or
sharp
or
pointed edges. This will prevent crimping and
damage to the wiring. If wiring passes through a hole
in
metal, use
a rubber grommet to prevent the
wire's
insulation from being cut by
the metal
edge
of
the hole.
DO
NOT
INSTALL
IN
LOCATIONS
WITH
HIGH
MOISTURE
OR
DUST.
Avoid installing the unit in locations with high incidence
of
moisture
or
dust. Moisture
or
dust that penetrates into this unit may
result
in
product failure.
Precautions
• Be sure to disconnect the cable from the
(-)
battery post before
installing your CDE-I03BT. This will reduce any chance
of
damage to the unit
in
case
of
a short-circuit.
• Be sure to connect the color coded leads according to the
diagram. Incorrect connections may cause the unit to
malfunction
or
damage to the vehicle's electrical system.
• When making connections to the vehicle's electrical system, be
aware
of
the factory installed components (e.g. on-board
computer). Do not tap into these leads to provide power for this
unit. When connecting the CDE-I 03BT to the fuse box, make
sure the fuse for the intended circuit
of
the CDE-I03BT has the
appropriate amperage. Failure to do so may result
in
damage to
the unit and/or the vehicle. When in doubt, consult your Alpine
dealer.
•
The
CDE-I
03BT
uses female RCA-type
jacks
for connection to
other units (e.g. amplifier) having RCA connectors.
You
may
need an adaptor to connect other units.
If
so, please contact your
authorized Alpine dealer for assistance.
• Be sure to connect the speaker
(-)
leads to the speaker
(-)
terminal. Never connect left and right channel speaker cables to
each other
or
to the vehicle body.
SERIAL NUMBER: _
INSTALLATION DATE: _
INSTALLATION TECHNICIAN: _
PLACE
OF
PURCHASE: _
- CDE-103BT 1
- Contents 3
- Operating Instructions 3
- Connections 4
- CenterH~le 6
- ~CAUTION 7
- Getting Started 8
- CD/MP3/WMA/ 10
- ~/II/ENT 11
- 4 Press and hold 12
- * The folder 13
- Sound Setting 14
- 3 Press and hold 15
- Other Functions 16
- L!7q(I)R 17
- BAND,~,~ 18
- Setting the AUX+ SETUP Mode 19
- Setting the AUX NAME mode 19
- Speakers 19
- 4 If this unit 20
- 10 input a 21
- 1 Press and hold 23
- ODD}:))! 24
- 3 Turn the 25
- Displaying 27
- Information 28
- MP3IWMAI~Ar; 28
- I UNIT ERROR I 29
- Indication 30
- BLUETOOTH.mode 30
- USB SECTION 31
- (7") 31
- (2") 31
- Installation 32
- ~Caution 32
- Precautions 32
- Mounting 33
- Microphone 33
- 'too 34
- (j) Battery Lead (Yellow) 35
- A?#ALPINE® 36
- StatefProv 38
- 38
- POSTAGE WILL 39
- PAID BY ADDRESSEE 39
Produits connexes et manuels pour Récepteur Alpine CDE-103BT
(68 pages)
(2 pages)
Récepteur Alpine ICS-X8 Manuel d'utilisateur
(96 pages)
(96 pages)
Récepteur Alpine ICS-X8 Manuel d'utilisateur
(11 pages)
(11 pages)
(35 pages)
(42 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.164 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels